Observation of metal on Si(0 0 1) by STM/STS and its consideration based on the first principles calculations

Local density of states (LDOS) is obtained by the first principles calculation based on the density functional theory on the Si(0 0 1)2 × 1 surface and on the surface with an Al dimer. At an Al dimer, LDOS has a high intensity in the conduction band region, which cannot be seen on the Si(0 0 1)2 × 1 surface. This tendency is observed in STS measurements as well. The possibility for a microelementary analysis is presented by applying this method to other metal atoms on the Si surface. Furthermore, it is pointed out that STS measurements should be always performed at the same tip-sample separation to obtain reproducible STS spectrums.     

High-velocity impact experiment of aluminum foam sample using powder gun

Porous materials such as aluminum foam have been investigated for possible use as impact shock absorbers in transportation aeronautic applications. However, the response of aluminum foam during impacts at high velocities of more than 100 m/s is not yet fully understood. A high-velocity impact experiment was therefore carried out to clarify impact shock absorption properties of aluminum foam. A one-stage powder gun was used to accelerate an aluminum foam sample to impact a rigid wall. Velocity and deformation of the aluminum foam sample during impact was studied using a digital high-speed video camera, while the pressure wave in the aluminum foam sample was measured using a PVDF gauge. The experimental observations revealed uneven collapse of the aluminum foam sample structure during high speed impact with a general stress plateau effect, typical for cellular material structures when subjected to quasi-static loading.     

CVCF inverter based on nonlinear control of instantaneous active and reactive power and its operation characteristics

This paper describes a direct‐power‐controlled CVCF inverter and presents its experimentally examined operation characteristics. The most important feature of this strategy is the direct selection of the switching states of the CVCF inverter to restrict errors between the feedback and command values of active and reactive power. In addition, this paper presents a theoretical analysis of the relationship between the instantaneous power and the switching state, which is essential for deriving a switching‐state table for the controller. The feasibility of the proposed method was verified through several computer simulations and experimental tests using a 2.0‐kVA prototype setup. The output voltages were confirmed to be stable sinusoidal waveforms with a total harmonic distortion of 1.13% under nonlinear load conditions. Excellent voltage balance was achieved by the proposed strategy even under unbalanced load conditions. © 2010 Wiley Periodicals, Inc. Electr Eng Jpn, 174(3): 62–69, 2011; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.21023     

Size Measurement of Polystyrene Latex Particles Larger than 1 Micrometer using a Long Differential Mobility Analyzer

We describe a newly constructed annular-type differential mobility analyzer (DMA) with an effective electrode length of 60 cm, which is longer than that of our original DMA (40 cm length). This long DMA was developed to extend the classification size of particles measuring up to 1.5 μm. As an application of this DMA, the mean diameters and standard deviations were determined for six samples of monodisperse polystyrene latex (PSL) particles ranging from 0.94 to 1.27 μm in nominal diameter. These PSL particles suspended in double-distilled water were aerosolized by a glass nebulizer and then introduced into the DMA. The mean diameters and standard deviations of these PSL particles were calculated by Ehara's method and compared with the nominal diameters and uncertainties. There was good correlation between the nominal diameters of these samples—particularly for recently certified samples—and the measured diameters. Classification of aerosol particles more than 1 micrometer in diameter using this DMA will be useful for many purposes.     

Potentials of GHG reductions from wastewater treatment for the CDM

The study aims to evaluate the potential of GHG (greenhouse gas) reductions by installing an anaerobic digester in a wastewater treatment facility in Southeast Asia. Then the break-even point of additional investment to reduce GHG is obtained by exchanging carbon price as emissions credits. In the project scenario, the wastewater treatment system has the digester, where methane (biogas) is produced and recovered. Compared with the baseline scenario, the biogas has calorific value to produce heat and electri...     

Crystallographic Texture Development in Bismuth Sodium Titanate Prepared by Reactive-Templated Grain Growth Method

Bi_0.5Na_0.5TiO₃ (BNT) and 0.94Bi_0.5Na_0.5TiO₃·0.06BaTiO₃ (BNT–BT) bulk ceramics with extensive 〈100〉 texture were prepared by the reactive-templated grain growth method, using platelike Bi₄Ti₃O₁₂ (BIT) particles as templates for BNT. Calcined compacts were composed of matrix grains with random orientation and 〈100〉-oriented grains transformed from aligned BIT particles, and the texture developed by the growth of oriented grains during sintering. Ceramics with extensive texture were obtained by using the starting mixture containing the maximum concentration of platelike BIT to form the maximum volume fraction of oriented grains.     

Fabrication and Microstructure Characterization of Ti3SiC2 Synthesized from Ti/Si/2TiC Powders Using the Pulse Discharge Sintering (PDS) Technique

Ti/Si/2TiC powders were prepared using a mixture method (M) and a mechanical alloying (MA) method to fabricate Ti₃SiC₂ at 1200°–1400°C using a pulse discharge sintering (PDS) technique. The results showed that the Ti₃SiC₂ samples with <5 wt% TiC could be rapidly synthesized from the M powders; however, the TiC content was always >18 wt% in the MA samples. Further sintering of the M powder showed that the purity of Ti₃SiC₂ could be improved to >97 wt% at 1250°–1300°C, which is ∼200°–300°C lower than that of sintered Ti/Si/C and Ti/SiC/C powders using the hot isostatic pressing (HIPing) technique. The microstructure of Ti₃SiC₂ also could be controlled using three types of powders, i.e., fine, coarse, or duplex-grained, within the sintering temperature range. In comparison with Ti/Si/C and Ti/SiC/C mixture powders, it has been suggested that high-purity Ti₃SiC₂ could be rapidly synthesized by sintering the Ti/Si/TiC powder mixture at relatively lower temperature using the PDS technique.     

Soluble and colorless polyimides with polyalicyclic structures [1]

Two tetracarboxylic dianhydrides with polyalicyclic structure, bicyclo[2.2.2]octane-2-endo, 3-endo, 5-exo, 6-exo-2,3:5,6-dianhydride (5a) and the all-exo isomer (5b), were synthesized in six steps using phthalic acid as a starting material. The dianhydrides were polymerized at 85–105°C in well-purified DMAc with aromatic diamines which were purified by two recrystallizations and then sublimation. The polyimides formed flexible and tough films, and were soluble in aprotic polar solvents such as DMAc. The 5%-weight loss temperatures were over 450°C. The polyimides possessed glass-transition temperatures in the range from 211 to 385°C. The polyimides films had a tensile modulus range of 1.5–2.6 GPa, a tensile strength range of 52–96 MPa, and an elongation range at break of 3–11%. The polyimide films showed cutoffs at wavelengths shorter than 320 nm and were entirely colorless. The colorlessness of the polyimide films was maintained up to 200°C when heated in air and to 400°C in a N₂ atmosphere.     

New class of cellulose fiber spun from the novel solution of cellulose by wet spinning method

A novel cellulose solution, prepared by dissolving an alkali-soluble cellulose, which was obtained by the steam explosion treatment on almost pure natural cellulose (soft wood pulp), into the aqueous sodium hydroxide solution with specific concentration (9.1 wt %) was employed for the first time to prepare a new class of multifilament-type cellulose fiber. For this purpose a wet spinning system with acid coagulation bath was applied. The mechanical properties and structural characteristics of the resulting cellulose fibers were compared with those of regenerated cellulose fibers such as viscose rayon and cuprammonium rayon commercially available. X-ray analysis shows that the new cellulose fiber is crystallographically cellulose II, and its crystallinity is higher but its crystalline orientation is slightly lower than those of other commercial regenerated fibers. The degree of breakdown of intramolecular hydrogen bond at C₃[X_am(C₃)] of the cellulose fiber, as determined by solid-state cross-polarization magic-angle sample spinning (CP/MAS) ¹³C NMR, is much lower than other, and the NMR spectra of its dry and wet state were significantly different from each other, indicating that cellulose molecules in the new cellulose fiber are quite mobile when wet. This phenomenon has not been reported for so-called regenerated cellulose fibers.